充電器 POWEREX
エグザアールシー
というメーカ
マニュアル
https://static.eleshop.nl/mage/media/downloads/mh-c9000-manual-en.pdf
FAQ
外観
ACアダプタは小さめ
クーラーファン搭載
熱くなったらファンを回して涼しくして安全に充電する
仕様
英語マニュアルから抽出
INPUT DC12V2000mA、センタプラス
操作は5モードあるって
Charge:充電
Refresh&Analyze:新鮮化
Break-in:何の事でしょう?
Discharge:放電
Cycle:何だろう?
充電方法
簡単な充電方法
スロットに充電池を入れるだけで充電してくれる
手順として
1、ACアダプタ繋ぐ
2、Insert AA or AAA battery.Insert the negative end first, as shown below.
充電池を入れて、マイナス側から入れる
3、If no key is pressed within ten seconds, the charger will proceed to
the default mode which is charging with 1000mA rate.
何も操作しなければ10秒後に1000mAで充電開始
複雑な充電方法
充電池毎に充電容量が違うから、充電池の性能を発揮させる為には設定が必要っぽい(興味ないけど)
FAQから抜粋
この情報を元に
手順として
1、ACアダプタ繋ぐ
2、Insert AA or AAA battery.Insert the negative end first, as shown below.
充電池を入れて、マイナス側から入れる
3、If CHARGE mode is selected:
The charger will prompt for the charging rate by flashing “SET CHG
RATE.” Use the UP and DOWN key to select the desired current.
Press ENTER to make the selection. Refer to the “General Battery
Education” section on choosing an appropriate rate.
充電モードを選択して
充電レートを設定する
この場合初期設定500mA
先の表からダイソー充電池なら1300mAだから
1000mAhの場合は500mA
amazon充電池なら、
2300mAhの場合は1100mA
成程、デフォルト充電だと強い場合がある
あまり複雑だと感じなかった
充電の強さ
マニュアルから抜粋
What is 0.1C, 0.2C, etc?
“C” stands for the battery capacity and the number preceeding it is the
fraction of the battery capacity. For example, 0.1C means 0.1 times the
capacity for the battery. For a 2700mAh battery, 0.1C would be 0.1 times
2700mAh which equals 270mA.
0.1Cとか0.2C
Cはバッテリの能力を表して、0.1Cは2700mAhの充電池なら270mA
Choosing the right charging & discharging rate
Charging at a rate below 0.3C and above 1.0C is not recommended.
Charging too slow may prevent the charger from terminating correctly.
Charging too fast may damage the battery.
Typically speaking, slower charging rate will yield better battery
performance but requires longer time. Faster charging rate may not
charge as fully and battery temperature can be higher.
As for the discharging rate, do not exceed 1.0C.
充電・放電レートの選択
0.3C~1.0C以外は推奨しない
放電は1.0Cを超えないこと
意外と簡単
操作もそれ程難しくなく、意外と簡単だと感じた
1.0Cで充電すれば1時間で充電完了
0.3Cで充電すれば3時間20分で充電完了する事が判った
電池を長持ちさせたかったら、0.3Cで3時間掛けて充電
速く充電したかったら1.0Cで充電
疑問
充電容量は設定できるのは判ったけど、どうやって満充電まで充電する事が解るんだろう?
電圧を見て、充電完了を判断している(らしい
総括
ACアダプタの間違いは必ず気を付ける(機械が壊れる)
機器の入力電圧と電流量を確認する
ACアダプタソケットの極性とACアダプタ本体の極性を必ず確認する
充電する時に、0.3Cを使うと電池に優しい
1.0Cを使うと早く充電が完了するけど、電池に優しくない
0.3C~1.0Cを外れるレートで充電するべきではない
デフォルトモードで充電するのはとても理に適っている
速く充電したい時だけ操作するのが良い
充電池の端子は常に磨いてあげると良いらしい